Mr.R
Hi Reed,
Payment sent for one pair inc' international shipping.
At that price I'd happily taken 2 pairs, but having just returned from a family holiday and also having to pay for a few other Ducati parts, I just haven't the funds at the moment.
Thanks again,
Steve R
nix510
Rocker sleeves
Thanks Reed-
Great news and payment on the way.....the other Nick
Jafa
Payment sent. Thanks.
rarebear
Payment sent, thanks reed
paul
motobob1000
I received my bushings today and am pleased as punch. they fit the rocker and yoke like butta.
Fast fast shipping too.
thanks, Bob Johnson
Hatman
Payment sent.
Speedmade
Shipped today
Mr R
Ufj
Rarebear
Nix510
Jafa
Hatman - will go out tomorrow
Mr.R
Hi Reed,
They arrived this morning, very pleased with them thanks again.
Edit...The last 2 days have been like an early Christmas for me thanks to fellow forum members, today the rear rocker sleeves arrived and yesterday I picked up a 916 crank from the local Post office.
The crank came as a result of an appeal on this forum for one and it gets better still...
The one I bought is a standard 916 Strada/Bip' item, Steve K aka Imola on here is going to swap this one for his 916SP crank, which saves me a lot of work lightening the standard 916 one.
Steve K/Imola is building a 916cc motor for his BBB Fabrications framed 888 special, he's not chasing BIG rwbhp.
I'm building a pretty hot but streetable 955cc motor for my '92 851 and I am chasing rwbhp so the lightweight SP crank's more suited to my wants/need.
Steve R
mikesps
Hi Reed,
They arrived in Malaysia today.
Many thanks,
Mike
Jafa
I got mine today ( have been away at work ). They are very nicely made. Thanks very much Speedmade for getting these made 😄
Hatman
Received my sleeves a while back -- thanks. Question: has anyone found a source for replacement needle bearings in the adjustable rocker/wishbone?
Jafa
Hatman wroteQuestion: has anyone found a source for replacement needle bearings in the adjustable rocker/wishbone?
Not yet, but if you do let us know because I will need some when I get to that stage.
Speedmade
They are available in the US from McMaster-Carr, but they don't ship international.
http://www.mcmaster.com/#5905k85/=oomgio
The bearings are 18mm OD x 14mm wide. I use the single seal end version.
It's the same bearings for the rocker and the u-link.
hindsight
Yow! - I just spotted this thread, are any of these left? - one of the sleeves on my project 851 is hosed.
Speedmade
Still have sets left. And I can get needle bearings.
PM sent.
Jafa
How many needle bearings are required for the complete setup? Don't have bike near me to check? Would you be able to post me however many are required Speedmade? I should have got them when I got your sleeves, didn't think about that 🙁
Speedmade
You need qty 4 of the same needle bearings to do the rocker and the u-link.
$19US a pair and $25 Priority International Post
Corse
Got my sleeves a little while back...thankyou!!!!!!!!
hindsight
Recieved mine in the post yesterday, thanks!
Hatman
Posted this to the technical section but didn't get any responses, so thought I'd try here. For those of you who replaced the bearings in the adjustable rocker, how did you get the old bearings out? I've tried using a drift from the opposite side to drive them out, but there's not much of a lip for the drift to catch. It looks like the "spacer" between the bearings is not a loose spacer (like in a wheel), but part of the arm itself, so pressing them out from one side doesn't appear to be an option. Can anyone confirm this? Any ideas for getting these out would be appreciated!
Thanks.
