+ Reply to Thread
Results 1 to 9 of 9

Thread: Corse dash

  1. #1
    Join Date
    Aug 2008
    Location
    Glos,England
    Posts
    400

    Default Corse dash

    Got a repro dash as pictured but can anyone confirm the sizes, I only have temperature gauge from road bike but no tacho, however the hole fot the temperature gauge appears to be to big.

    Was there a different one for race bikes, and can anyone tell me what the size of a race tachometer? I thought it would be same as road version which I think is 80mm.

    Any help greatly appreciated.
    Attached Images
    Surfking

  2. #2
    Join Date
    Feb 2011
    Location
    Denmark
    Posts
    537

    Default

    Quote Originally Posted by surfking View Post
    Got a repro dash as pictured but can anyone confirm the sizes, I only have temperature gauge from road bike but no tacho, however the hole fot the temperature gauge appears to be to big.

    Was there a different one for race bikes, and can anyone tell me what the size of a race tachometer? I thought it would be same as road version which I think is 80mm.

    Any help greatly appreciated.

    Hi, See my post few days back...

    You need the sponge frame ! (Road and race temp gauge same one)

    Hope this clarifies , can measure if you still want ?
    Attached Images

  3. #3
    Join Date
    Aug 2008
    Location
    Glos,England
    Posts
    400

    Default Corse dash

    Thanks For the pictures Stig, really helpful. I'll go on the hunt for a foam dash part then.

    Thank you

    Nick
    Surfking

  4. #4
    Join Date
    Feb 2011
    Location
    Denmark
    Posts
    537

    Default

    Quote Originally Posted by surfking View Post
    Thanks For the pictures Stig, really helpful. I'll go on the hunt for a foam dash part then.

    Thank you

    Nick
    Hi Nick...

    I don't think you will find one !, but i can send you the outlines and you can cut it out from a 20mm sponge sheet.. ?

    The one i have is NOS (its punched out) but not that nice of a finish (Hot wire or a fine saw cut, can do just as nice a part IMO) and for small money...

    Stig
    Attached Images
    Last edited by stiglarsenDK; 04-08-2017 at 12:03 PM.

  5. #5
    Join Date
    Aug 2008
    Location
    Glos,England
    Posts
    400

    Default

    Quote Originally Posted by stiglarsenDK View Post
    Hi Nick...

    I don't think you will find one !, but i can send you the outlines and you can cut it out from a 20mm sponge sheet.. ?

    The one i have is NOS (its punched out) but not that nice of a finish (Hot wire or a fine saw cut, can do just as nice a part IMO) and for small money...

    Stig
    Yes please Stig.

    Thank you very much.
    Surfking

  6. #6
    Join Date
    Feb 2011
    Location
    Denmark
    Posts
    537

    Default

    Quote Originally Posted by surfking View Post
    Yes please Stig.

    Thank you very much.
    MANUEL DXF ;-)

    Here the outline... if you print out on paper and ensure holes are about the right size (scale your print if needed)... rest will be fine as well !

    Good luck ... lets see/hear about the result :-) .. I have seen some foam sheets on EBAY UK..

    Thickness : 20MM


    NOTE : OUTLINE IS THE BACK SIDE !!
    Attached Images

  7. #7
    Join Date
    Mar 2009
    Location
    France
    Posts
    328

    Default

    It could be easier with that ;-)
    Attached Images

  8. #8
    Join Date
    Feb 2011
    Location
    Denmark
    Posts
    537

    Default

    Quote Originally Posted by BABA View Post
    It could be easier with that ;-)
    Thanks Baba, And even better !

    Do you have any experience with the foam type ... the original seems like a thermoplast foam.. very easy to damage / deform. (I have been thinking trying some rubber foam, with less deformation tendency (i.e moss type)

  9. #9
    Join Date
    Mar 2009
    Location
    France
    Posts
    328

    Default

    Not at all. Mine is NOS too, as the alloy dashboard.
    I haven't try to make another one. I just have redraw it in case of (and thinking that it could be usefull for someone else).

+ Reply to Thread

Similar Threads

  1. WTB Aluminum Dash - Early corse style
    By Marcoboxer in forum Wanted
    Replies: 1
    Last Post: 04-04-2016, 12:07 PM
  2. Corse Dash Foam
    By jr60 in forum For Sale
    Replies: 28
    Last Post: 02-22-2012, 07:48 AM
  3. Clocks in Corse Dash
    By jr60 in forum Technical Forum
    Replies: 44
    Last Post: 12-05-2011, 07:55 AM
  4. Corse race dash
    By sp2 boy in forum For Sale
    Replies: 1
    Last Post: 09-10-2010, 08:18 AM
  5. Replies: 9
    Last Post: 12-11-2008, 04:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts